Lenovo 6528 Manual do Utilizador

Installation and User GuideThinkServer TS200Machine Types: 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530

Antes de instalar este producto, lea la información de seguridad.Läs säkerhetsinformationen innan du installerar den här produkten.Important:Each caut

1. Position the front end of the front-panel assembly in the channel above drivebay 1 on the left side of the chassis.2. Push the front-panel assembly

7. Squeeze the spring clips 1 on the sides of the front USB connector assemblyand pull the assembly out of the back of the housing.8. Carefully pull

9. Reconnect the external cables and power cords; then, turn on the attacheddevices and turn on the server.Removing the rear adapter retention bracket

Removing the front adapter-retention bracketTo remove the front adapter-retention bracket, complete the following steps:1. Read the safety information

5. Disconnect the cables from the power-supply cage to the system board and allinternal components.6. Remove the four black screws that secure the pow

2. Install the four screws that secure the power-supply cage to the chassis.3. Connect the cables from the power-supply cage to the system board and a

CAUTION:When replacing the lithium battery, use only Part Number 33F8354 or anequivalent type battery recommended by the manufacturer. If your system

Removing a ServeRAID BR10-il controllerTo remove the ServeRAID BR10-il controller, complete the following steps:1. Read the safety information that be

plastic standoff.3. Connect the signal cable to the SAS/SATA controller.4. Install and lock the side cover (see “Installing the side cover” on page 33

Attention: Some cluster solutions require specific code levels or coordinated codeupdates. If the device is part of a cluster solution, verify that th

Statement 1:DANGERElectrical current from power, telephone, and communication cables ishazardous.To avoid a shock hazard:v Do not connect or disconnec

7. Press the ServeRAID-MR10i adapter firmly into the connector on the systemboard.8. Reconnect the cables to the new ServeRAID-MR10i adapter.Removing

1 Battery2 Battery carrier3 RAID adapter4 Connector for battery carrierb. Press the battery carrier into the connector on the ServeRAID adapte

2 PCI slot5. Press the ServeRAID-MR10is adapter firmly into the connector on the systemboard.6. Reconnect the cables to the new ServeRAID-MR10is ada

To remove a non-hot-swap power supply, complete the following steps:1. Read the safety information that begins on page vii and “Installation guideline

Installing a non-hot-swap power supplyThis procedure applies only to server models that have a non-hot-swap powersupply. See “Removing the hot-swap po

Removing the microprocessor and fan sinkTo remove the microprocessor and fan sink, complete the following steps:1. Read the safety information that be

c. Tip the top of the fan sink toward the front of the server while you slide itaway from the lower flange of the retention module; then, remove it fr

Installing a microprocessor and fan sinkTo install the microprocessor, complete the following steps:1. Touch the static-protective package that contai

a. Make sure that the fan sink retention lever is in the fully open position.Important: Be careful when you handle the microprocessor and fan sink.Do

Note:v Read the Safety information on page vii.v Read the “Installation guidelines” on page 29.To replace damaged or contaminated thermal grease on th

Statement 2:CAUTION:When replacing the lithium battery, use only Part Number 33F8354 or anequivalent type battery. If your system has a module contain

Removing the system boardTo remove the system board, complete the following steps:1. Read the safety information that begins on page vii and “Installa

9. Remove the eight screws (seven in front and one in rear) 1 that secure thesystem board to the chassis.10. Slide the system board toward the front

12. If you are instructed to return the system board, follow all packaginginstructions, and use any packaging materials for shipping that are supplied

5. Install the eight screws (seven in front and one in rear) that secure the systemboard to the chassis.6. Install any of the following components tha

108 ThinkServer TS200 Types 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide

Chapter 7. Configuring the serverThe following configuration programs come with the server:v Setup UtilityThe Setup Utility (formerly called the Confi

Table 14. Server configurations and applications for configuring and managing RAIDarrays (continued)Server configurationRAID array configuration(befor

Utility, the changes are reflected in the system summary; you cannot changesettings directly in the system summary.– Product DataSelect this choice to

- Network ConfigurationSelect this choice to view the system management network interface port,the IMM MAC address, the current IMM IP address, and ho

v User SecuritySelect this choice to set, change, or clear passwords. See “Passwords” for moreinformation.This choice is on the full and limited Setup

Statement 3:CAUTION:When laser products (such as CD-ROMs, DVD drives, fiber optic devices, ortransmitters) are installed, note the following:v Do not

password has access to only the limited Setup Utility menu; the user can set,change, and delete the power-on password, if the system administrator has

RAID controllersThe following table lists the various utilities available to configure RAID controllersbefore an operating system is installed.Table 1

1. After you turn on the power and when the computer is starting, you areprompted to press Ctrl + H when the following message is displayed:Copyright©

New ConfigurationClears the existing configuration and lets you create a newconfiguration.Add ConfigurationRetains the existing storage configuration

The EasyStartup program has the following features:v Self-booting DVDv Easy-to-use, language-selectable interfacev Integrated help systemv Automatic h

If you continue to the main program interface, you will have the following selectableoptions:v Compatibility notes: This selection provides informatio

– Integrated Mirroring Enhanced (IME) with hot-spare support (also known asRAID 1E)Use this option to create an integrated mirror enhanced array of th

4. To highlight the drive that you want to format, use the Up Arrow and DownArrow keys. To scroll left and right, use the Left Arrow and Right Arrow k

v Save response file: This task gives you the option of saving the information ona diskette or USB device as a response file for future installations

v SAS firmware is stored in ROM on the integrated RAID controller on the systemboard.v Major components contain vital product data (VPD) code. You can

Statement 4:≥ 18 kg (39.7 lb.) ≥ 32 kg (70.5 lb.) ≥ 55 kg (121.2 lb.)CAUTION:Use safe practices when lifting.Statement 5:CAUTION:The power control but

The IMM supports the following basic system management features:v Environmental monitor with fan speed control for temperature, voltages, fanfailure,

identify the server, and perform other management functions. Any standard Telnetclient application can access the SOL connection.Using the remote pres

2. On the Login page, type the user name and password. If you are using the IMMfor the first time, you can obtain the user name and password from your

v The server is not a domain controller. However, it is recommended to have theserver join a domain.v The account that you use to log in and to instal

v ASP.NETv ASPv CGIv Server Side Includesv Windows Authenticationv IIS 6 Metabase CompatibilityNote: When you select ASP.Net or ASP, a dialog box disp

Chapter 8. TroubleshootingThis chapter describes the diagnostic tools that are available to help you solveproblems that might occur in the server.If y

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the parts listing in the Ha

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the parts listing in the Ha

Keyboard, mouse, or pointing-device problemsv Follow the suggested actions in the order in which they are listed in the Action column until the proble

Memory problemsv Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the parts li

Statement 8:CAUTION:Never remove the cover on a power supply or any part that has the followinglabel attached.Hazardous voltage, current, and energy l

Microprocessor problemsv Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the

Monitor problemsSome monitors have their own self-tests. If you suspect a problem with yourmonitor, see the documentation that comes with the monitor

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the parts listing in the Ha

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the parts listing in the Ha

Power problemsv Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the parts lis

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the parts listing in the Ha

Software problemsv Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the parts

2. Check for loose cables in the power subsystem. Also check for short circuits, forexample, if a loose screw is causing a short circuit on a circuit

Solving undetermined problemsIf the diagnostic tests did not diagnose the failure or if the server is inoperative, usethe information in this section.

v System-event log: This log contains all IMM, POST, and system managementinterrupt (SMI) events. You can view the system-event log through the SetupU

DANGEROverloading a branch circuit is potentially a fire hazard and a shock hazardunder certain conditions. To avoid these hazards, ensure that your s

4. Click Downloads and drivers to download firmware updates.If IPMItool is installed in the server, you can use it to view the system-event log.Most r

POST error codesWhen you turn on the server, it performs a series of tests to check the operation ofthe server components and some optional devices in

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Chapter 1. IntroductionThis Installation and User Guide is intended to use with your Lenovo®ThinkServer™TS200 (Machine Types 6522, 6523, 6524, 6525, 6

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

1 Model and machine typeFor a list of supported optional devices for the server, go tohttp://www.lenovo.com/thinkserver and click the Options tab.No

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Related documentationThe Lenovo ThinkServer Documentation DVD contains documentation for theserver in Portable Document Format (PDF). The Lenovo Think

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Note: After you exit from the stand-alone memory diagnostic environment, youmust restart the server to access the stand-alone memory diagnosticenviron

To save the DSA log to a file on a diskette or to the hard disk, click Save Log onthe diagnostic programs screen and specify a location and name for t

Appendix A. Getting help and technical assistanceIf you need help, service, or technical assistance or just want more informationabout Lenovo products

Calling for serviceDuring the warranty period, you can get help and information by telephone throughthe Customer Support Center.These services are ava

Service methods and procedures vary by country, and some services might not beavailable in all countries. International Warranty Service is delivered

182 ThinkServer TS200 Types 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide

Appendix B. NoticesLenovo may not offer the products, services, or features discussed in this documentin all countries. Consult your local Lenovo repr

4 ThinkServer TS200 Types 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide

estimated through extrapolation. Actual results may vary. Users of this documentshould verify the applicable data for their specific environment.Trade

Lenovo makes no representation or warranties regarding non-Lenovo products andservices, including but not limited to the implied warranties of merchan

L’etiquette du système respecte la Directive européenne 2002/96/EC en matière deDéchets des Equipements Electriques et Electroniques (DEEE), qui déter

Table 17. Limits for particulates and gases (continued)Contaminant Limits1ASHRAE 52.2-2008 - Method of Testing General Ventilation Air-Cleaning Device

Battery return programThis product may contain a lithium or lithium ion battery. Consult your user manualor service manual for specific battery inform

batteries pour indiquer que la batterie ne doit pas être mise au rebut mais plutôtrécupérée en fin de cycle de vie selon cette norme.In accordance wit

This device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) this device may not cause harmful interfe

Dieses Produkt entspricht den Schutzanforderungen der EU-Richtlinie 2004/108/EG(früher 89/336/EWG) zur Angleichung der Rechtsvorschriften über dieelek

Japan Voluntary Control Council for Interference (VCCI) statementTaiwan Class A warning statementPeople’s Republic of China Class A warning statementK

IndexAacoustical noise emissions 11adapterhot-plug devices 92installing 57hot-plug 92PCI cardinstalling 60removing 55requirements 57scanning order 57S

Chapter 2. Server setup roadmapThe installation process varies depending on the configuration of the server when itwas delivered. In some cases, the s

diskette drive (continued)removing 44display problems 135documentation DVD 3drivecables 54removable-media 47, 48drive bays, internal 43drivesbay 1, 2,

HH8 heartbeat LED 24handling static-sensitive devices 31hard disk drivediagnostic tests, types of 131formatting 120problems 130status LED 17hard disk

LEDs (continued)rear of server 18LEDs and controlson the front of the server 15logssystem-event message 144lower bezelinstalling 69removing 34LSI Conf

reliability 12remote presence featurefunctions 8using 125removingadapter 55battery 89CD drive 44connector 62cover 32DIMMs 37diskette drive 44DVD drive

system board (continued)removing 104switches and jumpers 21system reliability guidelines 30system-board error LED 23system-error LED 17system-event lo

Printed in USA

6 ThinkServer TS200 Types 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide

Chapter 3. What is included with your serverThe TS200 server package includes the server, power cords, the ThinkServerDocumentation DVD, and software

v Remote presence capability and blue-screen captureThe remote presence feature provides the following functions:– Remotely viewing video with graphic

The command-line interface provides direct access to server managementfunctions through the IPMI 2.0 protocol. Use the command-line interface to issue

SpecificationsThe following information is a summary of the features and specifications of theserver. Depending on the server model, some features mig

Table 2. Features and specifications (continued)RAID controllers:v ServeRAID BR10ilv ServeRAID-MR10iv ServeRAID-M1015v ServeRAID M5015v ServeRAID MR10

Reliability, availability, and serviceabilityThree important server design features are reliability, availability, and serviceability(RAS). The RAS fe

v Wake on LAN capabilityChapter 3. What is included with your server 13

ThinkServer TS200 Types 6522, 6523, 6524, 6525,6526, 6528, 6529, and 6530Installation and User Guide

14 ThinkServer TS200 Types 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide

Chapter 4. Server controls, LEDs, and powerThis section describes the controls and light-emitting diodes (LEDs) and how to turnthe server on and off.F

1 Simple-swap hard disk drive 6 Hard disk drive activity LED2 DVD drive activity LED (green) 7 System error LED3 Front information panel 8

Fading on and off: The server is in a reduced-power state. To wake the server,press the power-control button or use the IMM Web interface. See “Loggin

Rear viewThe following illustration shows the connectors and LEDs on the rear of the server.1 USB 3 and 4 5 Serial (Com1)2 USB 1 and 2 6 Power

System-board internal connectorsThe following illustrations show the internal connectors and switches on the systemboard.MicroprocessorHeatsinkOrienta

1 DIMM 1 11Fan 1 connector 21Slot 2: PCIe2 x8, 25w2 DIMM 2 12Hard disk backplaneconfigurationconnector22Slot 1: PCIe2 x8, 25w3 DIMM 3 1

3 Ethernet connector 1 7 SW1 (NMI button)4 USB connectors 1 and 2System-board switches and jumpersThe following illustration shows the switches

Important:1. Before you change any switch settings or move any jumpers, turn off the server;then, disconnect all power cords and external cables. Revi

Table 4. System-board LEDs (continued)LED DescriptionBaseboard managementcontroller heartbeat LEDThis LED flashes to indicate that the IMM is function

Note: Before using this information and the product it supports, read the general information in Appendix B, “Notices,” on page 183and the Warranty an

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the parts listing in the Ha

1 AC power LED2 DC power LED3 Fault LED4 Fault LED5 Power LEDThe following table describes the problems that are indicated by variouscombina

Table 5. Power-supply LEDsPower-supply LEDsDescription Action NotesAC DC ErrorOff Off Off No ac power tothe server or aproblem with theac power source

the server is connected to ac power, the power-control button becomes active (thepower-on LED flashes slowly). You can turn on the server by pressing

Turning off the serverWhen you turn off the server and leave it connected to ac power, the server canrespond to requests to the service processor, suc

Chapter 5. Installing and replacing optional devicesThis chapter provides detailed instructions for installing optional hardware devices inthe server.

devices. However, you must turn off the server before performing any steps thatinvolve removing or installing adapter cables or non-hot-swap optional

v Avoid wearing loose-fitting clothing on your forearms. Button long-sleeved shirtsbefore working inside the server; do not wear cuff links while you

Server componentsThe following illustration shows the major components in the server.1 Cover 10 SATA hard disk drive (some models)2 Non-hot-swap

Attention: Operating the server for more than 30 minutes with the side coverremoved might damage server components. For proper cooling and airflow, re

ContentsSafety ...viiChapter 1. Introduction ...1Notices and statements in this document...2R

3. Position the lip on the bottom edge of the side cover on the ledge on the bottomof the chassis; then, rotate the cover up to the chassis. Press dow

5. Lift the lower bezel to disengage the two bottom tabs from the chassis. Set thelower bezel aside.Chapter 5. Installing and replacing optional devic

6. Carefully pull the two bezel clips 1 on the left side of the upper bezel awayfrom the chassis; then, rotate the upper bezel to the right side of

2. Rotate the top of the lower bezel up to the chassis; then, press the blue releasetab on the right side of the lower bezel and completely close the

6. If you are instructed to return the DIMM, follow all packaging instructions, anduse any packaging materials for shipping that are supplied to you.I

where:ggg is the total capacity of the DIMM (for example, 1GB, 2GB, or 4GB)e is the number of ranks1 = single-rank2 = dual-rank4 = quad-rankff is the

v The following table lists the supported UDIMM population.Table 6. Supported UDIMM population per channelDIMMs slotsper channelDIMMs installedin each

v The following table lists the supported RDIMM population.Table 9. Supported RDIMM population per channelDIMMs slotsper channelDIMMs installedin each

To install a DIMM, complete the following steps:1. Read the safety information that begins on page vii and “Installation guidelines”on page 29.2. Turn

If you have other devices to install or remove, do so now; otherwise, go to“Completing the installation” on page 67.Removing and installing internal d

Power and signal cables for internal drives ...54Removing an adapter ...55Installing an adapter ...57

The following notes describe the types of drives that the server supports and otherinformation that you must consider when installing a drive:v Make s

1 Release buttons2 Drive retainer clip7. Remove the drive retainer clip from the side of the drive. Save the clip to usewhen you install the repla

Statement 3:CAUTION:When laser products (such as CD-ROMs, DVD drives, fiber optic devices,or transmitters) are installed, note the following:v Do not

1 Release buttons2 Drive retainer clip5. Push the drive into the bay.6. Connect the power and signal cables to the drive.Note: Route the signal ca

1 EMC shield2 Tape drive3 Drive retainer clip9. If you are instructed to return the drive, follow all packaging instructions, anduse any packagi

8. Set any jumpers or switches on the drive according to the documentation thatcomes with the drive.9. Remove the drive retainer clip from the side of

To remove a hot-swap hard disk drive, complete the following steps:1. Read the safety information that begins on page vii and “Installation guidelines

Table 13. IDs of the hot-swap drives (models with four drive bays)Drive bay ID40516273Installing a hot-swap hard disk driveThis procedure applies only

1. Touch the static-protective package that contains the drive to any unpaintedmetal surface on the server; then, remove the drive from the package an

Removing a simple-swap hard disk driveThis procedure applies only to server models that have simple-swap SATA hard diskdrives.Attention: Simple-swap h

Starting the Setup Utility ...110Setup Utility menu choices ...110Passwords ...113Using the Boo

Installing a simple-swap hard disk driveThis procedure applies only to server models that have simple-swap SATA hard diskdrives.Attention: Simple-swap

v The drives that are preinstalled in the server come with power and signal cablesattached. If you replace any drives, remember which cable is attache

7. Remove the expansion-slot screw 2 at the rear of the adapter 3 if any.8. Carefully grasp the adapter by its top edge or upper corners. And pull

Installing an adapterThe following notes describe the types of adapters that the server supports andother information that you must consider when you

6. Remove the screw that secures the expansion-slot cover to the chassis. Storethe expansion-slot cover and screw in a safe place for future use.Note:

8. If you are installing a full-length adapter, remove the blue adapter guide (if any)from the end of the adapter.1 Adapter guide9. Carefully grasp

Attention: To avoid breaking the retaining clips or damaging the adapterconnector, open and close the clips gently.5. Carefully grasp the end of the a

9. Take the other end of the signal cable that is attached to the drive backplanesection for drive bays 0 through 3 (as labeled on the front of the dr

5. Align the flash device with the connector on the system board and push it intothe connector until it is firmly seated.6. Press down on the retainin

4. If you are instructed to return the virtual media key, follow all packaginginstructions, and use any packaging materials for shipping that are supp

Diagnostics messages...178Appendix A. Getting help and technical assistance ...179Before you call ...179

Removing a hot-swap power supplyThis procedure applies only to server models that have hot-swap power supplies.See “Installing a non-hot-swap power su

To remove a hot-swap power supply, complete the following steps:1. Read the safety information that begins on page vii and “Installation guidelines”on

1 Release lever2 Hot-swap power supply2. Using the handle, push the power supply toward the front of the chassis until itlocks into place.3. Conne

4. Thread the cable through the rope clip and around an object that is not part ofor permanently secured to the building structure or foundation, and

68 ThinkServer TS200 Types 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide

2. Install the lower bezel:a. Insert the two bottom tabs on the lower bezel into the matching holes in thefront of the chassis.b. Rotate the top of th

Reinstalling the side coverIf you removed the side cover, reinstall it.Note: The rear adapter-retention bracket rests against the server side cover. Y

Connecting the cablesAttention: To prevent damage to equipment, connect the power cords last.If the server cables and connector panel have color-coded

72 ThinkServer TS200 Types 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide

Chapter 6. Installing and replacing customer replaceable unitsRemoving the rear system fanAttention:v Replace a failed fan within 48 hours.v To ensure

SafetyBefore installing this product, read the Safety Information.Antes de instalar este produto, leia as Informações de Segurança.Pred instalací toho

Installing the rear system fanAttention:v Replace a failed fan within 48 hours.v To ensure proper cooling and airflow, do not operate the server for m

Removing the hard disk drive fan assemblyThis procedure applies only to server models that have a hard disk drive fanassembly.Attention:v Replace a fa

9. Pull out on the hard disk drive fan assembly release tabs; then, rotate theassembly away from the drive cage slightly.1 Release tabs2 Hard disk

1 Release tabs2 Hard disk drive fan assembly3 Slot2. Route the hard disk drive signal and power cables through the slots on theedge of the hard

5. Connect the hard disk drive fan assembly cable to the system board (see“System-board internal connectors” on page 19 for the location of the hard d

1 Retaining tab2 Drive cage release tab3 Locating pins4 Simple-swap backplate5 Retaining latch11. Lift the simple-swap backplate out of the

1 Retaining tab2 Drive cage release tab3 Locating pins4 Simple-swap backplate5 Retaining latch2. Tilt the top of the simple-swap backplate t

Removing the SAS/SATA hard disk drive backplaneThis procedure applies only to hot-swap server models with a SAS/SATA hard diskdrive backplane installe

10. Tilt the top of the hard disk drive backplane away from the drive cage until it isclear of the locating pins.11. Lift the SAS/SATA hard disk drive

6. Install the hard disk drive fan assembly onto the hard disk drive cage (see“Installing the hard disk drive fan assembly” on page 76).7. Install the