Lenovo IdeaCentre Q200 Manual do Utilizador

www.lenovo.comVersion 1.0WORLDWIDE PARTNERIdeaCentre QHardware Replacement Guide3103275631032756_HRG_FM_EN.indd 1 2007.12.21 4:57:27 PM

7Hardware Replacement GuideX-1X-2T-2V-2SDVIX-2L&RFMT-2V-2VSV-2 ———— The external VGA Card may have some of these connectors, but not have all of

8Hardware Replacement GuideKey to symbols used in the above illustrations of the rear of the chassis: ——— Power Connector: To supply power to the comp

9Hardware Replacement GuideV ——— Video Connector: To connect with the Video to S-Video converting cable provided in the computer. (Some models are eq

10Hardware Replacement GuideMicroprocessor and heat sink 1394 connectorMicroprocessor fan connector Serial (com2) connectorMemory connector 1 Front au

11Hardware Replacement GuideReplacing hardwareAttentionDo not remove the computer cover or attempt any repair before reading the “Important safety inf

12Hardware Replacement GuideRemoving and replacing the front bezelTo remove and replace the front bezel: 1. Open the computer cover. Refer to “Openin

13Hardware Replacement Guidetop of the chassis. 4. Refer to the “Completing the installation”.Replacing a memory module AttentionDo not remove the co

14Hardware Replacement Guide6. Refer to the “Completing the installation”. Replacing the power supply AttentionDo not remove the computer cover or at

15Hardware Replacement Guide2. Open the computer cover. Refer to “Opening the computer cover”. Note: For this procedure, it helps to lay the compute

16Hardware Replacement Guide4. Disconnect the power supply cables from the system board and from all drives. Refer to “Identifying parts on the syste

Hardware Replacement Guide 31032756_HaWaii-HRG_EN.indd 39 2008.1.8 3:31:49 PM

17Hardware Replacement Guide7. Install the new power supply assembly into the chassis so that the screw holes in the power supply assembly align with

18Hardware Replacement Guide8. Lift the failing heat sink and fan assembly off the system board. 9. Use the thermal grease syringe to place five drop

19Hardware Replacement Guide13. Reconnect the disconnected cables to the system board. 14. Refer to the” Completing the installation”.Replacing the sy

20Hardware Replacement Guide8. Lift the system board out of the chassis carefully. Note: You might have to tilt the front end of the system board be

21Hardware Replacement Guide13. Lift the heat sink and fan assembly off the failing system board. Place the heat sink on its side so that the thermal

22Hardware Replacement GuideImportantTouch only the sides of the microprocessor. Do not touch the gold contacts on the bottom.15. Lift the microproces

23Hardware Replacement GuideImportantTo avoid damaging the microprocessor contacts, do not tilt the microprocessor when installing it into the socket.

24Hardware Replacement GuideTo replace the heat sink assembly: 1. Open the computer cover. Refer to “Opening the computer cover”.2. Pivot the drive

25Hardware Replacement Guide7. Lift the heat sink and fan assembly off the failing system board. Note: Place the heat sink on its side on a clean,

26Hardware Replacement GuideImportantDo not touch the gold contacts on the bottom of the microprocessor. When handling the microprocessor, touch only

ContentsOverview ... 1Chapter 1 Locations ...

27Hardware Replacement Guide12. Holding the microprocessor with your fingers, position the microprocessor so that the notches on the microprocessor are

28Hardware Replacement Guide16. Install the heat sink and fan assembly on the system board. 17. Connect the heat sink and fan assembly cable to the sy

29Hardware Replacement Guide3. Disconnect the signal and power cables from the hard disk drive. 4. press the release button to pull the drive and br

30Hardware Replacement Guide5. Use the blue handle to remove hard disk drive from drive bay. 6. Slide the new hard disk drive into the drive bay. 7.

31Hardware Replacement Guide5. Slide the new optical drive into the bay from the back until it snap into position. 6. Connect the signal and power c

32Hardware Replacement Guide3. Pulling the adapter out of the adapter connector by opening the retaining clips as shown.4. Install the new adapt

33Hardware Replacement Guide5. Ensure the adapter is fully seated into the adapter connector. 6. Pivot the adapter latch to the closed position to s

34Hardware Replacement Guideconnector at the rear of the computer or to a USB connector at either the front or rear of the computer.4. Disconnect

35Hardware Replacement Guide4. Disconnect the failing mouse cable from the computer. 5. Connect the new mouse cable to the connector. 6. Refer to t

36Hardware Replacement GuideImportantCorrectly route all power supply cables to avoid interference with the drive bay assembly. Keep cables clear of t

1Hardware Replacement GuideOverviewThis guide is intended to be used by customers who are replacing Customer Replaceable Units (CRUs) as well as train

37Hardware Replacement GuideAppendix. StatementThanks for using Lenovo products.Carefully read all documents shipped with your computer before you ins

38Hardware Replacement GuideLenovo is trademark of Lenovo (Beijing ) Co., Ltd.Microsoft is the registered trademark of Microsoft Corporation.Microsoft

2Hardware Replacement Guidecan obtain one online from the Support Web site at http://www.lenovo.com/support. Additional information resources If you h

3Hardware Replacement Guideand your body. • When possible, remove the new part from the static-protective packaging, and install it directly in the c

4Hardware Replacement GuideLocationsChapterThis chapter provides illustrations to help locate the various connectors, controls and components of the c

5Hardware Replacement GuidePower supply Hard disk driveMicroprocessor fan and heat sink Optical driveMemory connectors(2) card readerPCIe adapter card

6Hardware Replacement GuideF-2 Digital connector(open the Digital Panel)MS/Duo/ProDuo[D-4][D-1][D-1][D-2][D-3]xDCF I/II/MDSD/Mini/HC/MiniHCMMC/RS/Plus